ILCE-7S Firmware Update For Windows

Details

Important Notes:

• Please close all other application software before upgrading the system software.
• Prevent your computer from sleep mode beforehand.
• When performing the system software update, please use a fully charged rechargeable battery pack NP-FW50 or the AC adaptor AC-PW20 (sold separately).
• Do not remove the battery or AC adaptor during the update; otherwise, the camera may become inoperable due to the sudden power shutdown.
• Do not be connected to other apparatuses except your computer.
• Remove the memory card from the camera beforehand.

1. Download the update file
   Download the file to your computer. Please save the downloaded file onto the Desktop of your computer (recommended).
   
   For Windows8.1 and Windows10 users:
   Under the initial settings of Internet Explorer, the update file will be saved in the Downloads folder. Click the Desktop tile from the Start screen and find the downloaded file in the Downloads folder by using Explorer.


2. Start up Firmware Updater
   Close all currently running programs on your computer, then double click Update_ILCE7SV320.exe to start up Firmware Updater.
   


3. Check the USB connection mode
   
   1. Turn on the camera.
   2. According to the Firmware Updater instructions, select Menu > Setup > 4 > USB Connection on the camera, then check if Mass Storage is selected. If a mode other than Mass Storage is selected, select Mass Storage.
      


4. Connect the camera to the computer
   Remove the memory card from the camera beforehand.
   1. connect the camera to the computer with the supplied USB cable. If the computer cannot find the camera, the message “Could not find the camera for this update.” appears on the computer display. Try the following if this happens.
      
      
      • Disconnect the USB cable and connect it again.
      • If the computer has multiple USB terminals, try with the other terminals.
   
   Note: When the camera is connected to the computer, the LCD screen of the camera turns off. Please proceed to the next step.
   
   
   2. Confirm is displayed on the task tray at the lower right corner of the computer screen.
      
      Note: If is not displayed on the task tray, please proceed to the next step.
   
   
   3. After confirming the above, click Next on the Firmware Updater. The following image appears on the Firmware Updater.
      
      
      And the following image appears on the LCD screen of the camera.
      
      
      Note: From now on, do not turn off the camera until the system software update is completed.


5. Check if the update is required
   
   1. After confirming the LCD monitor of the camera, click Next. The current version and the version after the lower left part of the screen.
      
      Upgrade is required
      
      
      Note: If the below screen appears, the update is not required. According to the message, stop the USB connection and click Finish. Turn off the camera, remove the battery pack or the AC adaptor, and then turn on the camera again.
      
      Upgrade is not required
      
   
   
   2. After confirming Current version is Ver. 3.10 or earlier, click Next.


6. Reset the camera
   1. Click on the task tray at the lower right corner of the computer screen to stop the USB connection.
      
      
      Note: Please keep the USB cable connected even after stopping the USB connection on the computer with the above operation.
      Note: If is not displayed on the task tray, please proceed to the next step.
   
   
   2. Press the center of the control wheel to execute.
      
      
      
      Note: The screen turns off when the center of the control wheel is pressed. Please proceed to the next step.
   
   
   3. Click Next on the Firmware Updater.
      


7. Start the update
   
   1. After resetting, reconnection of the camera is verified, and the following image appears.
      
   2. Click Run to start the update. The progress bar appears while updating (approximately 15 minutes).
   
   Note: Do not turn off the camera or disconnect the USB cable while updating.


8. Complete the update
   
   1. When the update is completed, the camera will automatically restart. It may take a few minutes to restart. Make sure the camera is turned on and wait until the LCD screen appears again. Click Finish when the LCD screen appears.
      
      
      Note: After automatically restarting of the camera, a restoration screen may be displayed.
      
      
      While it is displayed, please do not disconnect USB cable. And after finishing a restoration, the camera may power off automatically. But the update is completed.
   
   
   2. Click on the task tray at the lower right corner of the computer screen to stop the USB connection.
      
      Note: If is not displayed on the task tray, please proceed to the next step.
   
   
   3. Disconnect the USB cable.


9. Check the system software version
   Follow the instruction to confirm the system software version is Ver. 3.20.
   
   
   1. Select Menu > Setup > 6 > Version on the camera.
   2. The system software version is displayed.